Step-2; Step-3; On the backside of the PS4, where the connection ports are located, remove stickers, and below them screws that we need to unscrew. Wedge a plastic opening tool into the opening and slide it up towards the joystick. Underneath the battery you will see white plastic frames. The back cover should now be easy to remove. How to disassemble and reassemble PS4 DualShock 4 Controller. Include your email address to get a message when this question is answered. Disassemble your PS4 controller and clean the insides of the controller but focus on the PS button Plugin a USB cable and see if it works, perform a hard reset of the controller Test the controller USB port and batteries to diagnose the issue At this point you can take it out and replace it. That $@$* Is a &&^&^$^ paradox. On one side of the controller, pull the number 2 trigger (the bigger one) from the controller. Lift and remove both of these from the controller as well. Xinkaize High Quality New Cross Screwdriver Disassemble Repair Tool para PS4 Controller DualShock 4: Amazon.es: Electrónica Selecciona Tus Preferencias de Cookies Utilizamos cookies y herramientas similares para mejorar tu experiencia de compra, prestar nuestros servicios, entender cómo los utilizas para poder mejorarlos, y para mostrarte anuncios. © 2021 iFixit — Licensed under Creative Commons — Privacy — wikiHow is where trusted research and expert knowledge come together. If it is not responsive, see if you can solder the wires to the button again. Cheapest how_to_disassemble_a_ps4 online on TVC-Mall.com, wholesale now for inexpensive how_to_disassemble_a_ps4. So my controller decided to stop charging (still stayed on until the battery completely dained) a couple weeks ago so I bought a new charging port and ribbon and replaced it put it all back together just for it to work the same not charging but on so I figured maybe it was the battery all along but this time I took my other new controller apart so I could test the battery by connecting it to the new controller to see if it will take charge which they would take charge on the new controller but when I took the new ones and put it in the old on it still wouldn't take charge I have no Idea what else to do everything else works it just won't charge even the light is still on but if I keep it connected to a USB cable it will stay on since the battery was dead but the battery status remains the same. Pinch the left handle of the controller to introduce an opening. This article has been viewed 34,614 times. How to Disassemble and Reassemble a PS4 controller YouTube Descargar Comparte con tus amigos en las redes sociales. But with the arrival of COVID-19, the stakes are higher than ever. This makes replacing each components easier. Underneath the white frame there should be a thin, green, plastic film. In addition, remove the hard drive. Once done, the controller will easily come apart. This teardown is not a repair guide. You can also try disassembling and getting to the root cause (keep reading below to find out how you can disassemble your PS4 controller). To remove the logic board, unscrew the screw, before lifting the logic board out. If you need to change the battery out, do so by using blunt forceps to gently unplug the battery from the motherboard. PS4 Slim model location: turn the console over and at the end where the HDMI output is located, your revision of the console will be indicated a little higher in the recess. Reply. We are not responsible for any damages. We tore it apart to see what's different. You should follow the instructions to disassemble and see if the button behind R2 is responsive. Then you you move it up and you can wiggle it through the arc. On one side of the controller, pull the number 2 trigger (the bigger one) from the controller. The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen. If you think that the controller doesn't work, make sure the device is on. The motors are attached to the metal frames with adhesive. Remove the single 6.0 mm Phillips screw found below the battery retainer with the Phillips #00 Screwdriver. Lift the battery from the logic board. % of people told us that this article helped them. Next you’ll need to pry up the case near left and right triggers. To prevent loss, maintain a controlled work field. When you lift the logic board out of the controller, the joysticks will be attached to the logic board. Step 4 Use a small prying tool to pull apart hard to reach areas. To repair your DualShock 3, use our service manual . If you don’t like holding down a button and rotating the analog stick, another option would be to use the PS4’s gyroscope as a mouse. You should be looking at the back of the controller. There should also be two additional white plastic frames that hold the buttons. Pull down on the plier to crack open the casing. If so, try to move the casing closer towards the button. The Xbox One controller is generally accepted as one of the best video game controllers around, but they still break down and need repairs from time to time. Wedge a plastic opening tool into the opening and slide it up towards the joystick. Check out Evil Controllers for handmade gaming controllers and see all that we have to offer! Small parts may make them hard to find. {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/f\/f1\/Disassemble-a-Dual-Shock-3-Controller-Step-1.jpg\/v4-460px-Disassemble-a-Dual-Shock-3-Controller-Step-1.jpg","bigUrl":"\/images\/thumb\/f\/f1\/Disassemble-a-Dual-Shock-3-Controller-Step-1.jpg\/aid6953682-v4-728px-Disassemble-a-Dual-Shock-3-Controller-Step-1.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"